Lamp shades for pendant, table and floor lamps

Pendant and ceiling

The shade hangs from a cord set or a ceiling rose you already own, at the drop your ceiling gives you.

Render pending
The shadeThe ridged wall from across a room, unlit, on one ground.
Render pending
Switched onOver a table in a dark room, with the light landing on the table and not the ceiling.
Render pending
The ridge, closeThe vertical ridge against the printed layer grain, at arm's length.
Render pending
The ring seatThe 40 mm shade ring seat, which is where your cord set takes over.

Ridge Pendant 280

LT-HG-280

Price on request

A wide, shallow pendant shade for over a table, open at the top and at the bottom. The ridged outer wall reads as a set of vertical lines from across the room and as a printed layer grain from arm's length, and those are the same lines. It hangs from a standard 40 mm shade ring on a cord set you already own.

Code: LT-HG-280
Size: 280 mm across, 140 mm tall
Wall: 1.4 mm nominal
Material: Virgin PETG, printed, translucent; Stainless steel shade ring seat, bought in, 40 mm
It takes: An E27 lampholder with a 40 mm shade ring.
Bulb: An LED, up to 12 W and 65 mm across the envelope
Clearance: 47.5 mm from the widest point of the bulb to the nearest printed surface
Openings: Open at both ends. 96 mm clear at the top, 272 mm clear at the bottom.
Yours to choose: The lampholder and shade ring, the cord set or the stem, the switch, the plug and the bulb.
Colour: unpigmented natural by default, or warm white, pale sand
Weight: 480 g, the printed part alone
Made to order: The outer diameter, 200 to 300 mm. Wall section, the 40 mm ring seat, the top opening and the clearance minimum stay as drawn. Height scales with the diameter at a fixed 1:2 ratio. 300 mm is the top of the range, because it is the build envelope and one seamless piece with no joint ring is the point of it.
Lead time: 9 to 13 days, printed after it is ordered
Printed: 0.16 mm layers, 3 perimeters, upright, narrow opening down, about 16 hours on the machine

Why this shapeWide and shallow, so the light lands on the table and not on the ceiling. It is 280 mm across rather than a globe because a globe would close around the top of the bulb, and this one is open at both ends. The ridge began as a way of making the layer line look deliberate and ended up being the thing you see from across the room.

Drawn for an LED bulb. LED runs cool and lasts for years, and this shade is drawn around one at 12 W and 65 mm. Buy the next bulb to the same two numbers and it is the right bulb for it. The instructions are behind the QR code on the shade.

Make yours Instructions

Review and request

Request Ridge Pendant 280 · LT-HG-280. We confirm the size, colour, price and timing before printing.

Render pending
The coneOne cone, unlit, on one ground.
Render pending
Three, at staggered dropsA run of three down a stairwell, each at a different drop.
Render pending
The pointThe open point of the cone, which is the top opening.
Render pending
Scale140 mm across, over a kitchen counter.

Cluster Cone 165

LT-HG-165

Price on request

A small cone, sold one at a time and drawn to be hung in threes over a counter or down a stairwell at staggered drops. It is open at its point and at its mouth. It takes an E14 lampholder with a 28 mm shade ring, and the cord set is yours.

Code: LT-HG-165
Size: 140 mm across, 165 mm tall
Wall: 1.2 mm nominal
Material: Virgin PETG, printed, translucent; Stainless steel shade ring seat, bought in, 28 mm
It takes: An E14 lampholder with a 28 mm shade ring.
Bulb: An LED, up to 6 W and 45 mm across the envelope
Clearance: 36.5 mm from the widest point of the bulb to the nearest printed surface
Openings: Open at both ends. 44 mm clear at the point, 134 mm clear at the mouth.
Yours to choose: The lampholder and shade ring, the cord set or the stem, the switch, the plug and the bulb.
Colour: unpigmented natural by default, or warm white, pale sand
Weight: 175 g, the printed part alone
Made to order: The height, 120 to 240 mm. Mouth diameter, wall section, the 28 mm ring seat and the clearance minimum stay as drawn. A taller cone is a narrower cone of light, which is the reason to order one.
Lead time: 6 to 9 days, printed after it is ordered
Printed: 0.12 mm layers, 3 perimeters, upright, point down, about 7 hours on the machine

Why this shapeA cluster wants small shades, and a small shade is the harder drawing, because there is less room inside it for everything. The cone narrows to its point, keeps the widest part of the wall where the bulb is widest, and hangs well in threes. A small drum was drawn first and did neither.

Drawn for an LED bulb. LED runs cool and lasts for years, and this shade is drawn around one at 6 W and 45 mm. Buy the next bulb to the same two numbers and it is the right bulb for it. The instructions are behind the QR code on the shade.

Make yours Instructions

Review and request

Request Cluster Cone 165 · LT-HG-165. We confirm the size, colour, price and timing before printing.

Floor and table

The shade sits on a harp, a carrier ring or a stem and carries its own weight.

Render pending
The columnThe full cylinder, unlit, on one ground.
Render pending
Switched onReading light out of the bottom, a soft band through the wall, the top left open.
Render pending
On its harpThe shade seated on a harp and finial, with the carrier ring alternative beside it.
Render pending
Scale260 mm tall, beside a chair.

Column Shade 260

LT-ST-260

Price on request

A tall open cylinder for a floor lamp, sitting on a standard harp and finial or on a 40 mm carrier ring. It has the widest bore in the catalogue, 200 mm, and the largest clearance, 60 mm. Reading light comes out of the bottom, a soft band comes through the wall, and the top is left open on purpose.

Code: LT-ST-260
Size: 220 mm across, 260 mm tall
Wall: 1.6 mm nominal
Material: Virgin PETG, printed, translucent; Stainless steel carrier ring seat, bought in, 40 mm
It takes: An E27 lampholder on a harp and finial, or a 40 mm carrier ring.
Bulb: An LED, up to 15 W and 65 mm across the envelope
Clearance: 67.5 mm from the widest point of the bulb to the nearest printed surface
Openings: Open at both ends. 200 mm clear at the top, 216 mm clear at the bottom.
Yours to choose: The lampholder and shade ring, the cord set or the stem, the switch, the plug and the bulb.
Colour: unpigmented natural by default, or warm white, pale sand
Weight: 640 g, the printed part alone
Made to order: The height, 180 to 300 mm. Diameter, bore, wall section, carrier seat and the 60 mm clearance minimum stay as drawn. A taller column is a narrower pool of light on the floor and a longer soft band on the wall behind it.
Lead time: 11 to 15 days, printed after it is ordered
Printed: 0.16 mm layers, 4 perimeters, upright, about 21 hours on the machine

Why this shapeA floor lamp shade is at eye level standing and below it sitting, so it is closed at the sides and open at the bottom. Reading light comes out of the bottom, a soft band comes through the wall, and the top is left open. It carries the widest bore here, 200 mm, which is what lets it also be the tallest.

Drawn for an LED bulb. LED runs cool and lasts for years, and this shade is drawn around one at 15 W and 65 mm. Buy the next bulb to the same two numbers and it is the right bulb for it. The instructions are behind the QR code on the shade.

Make yours Instructions

Review and request

Request Column Shade 260 · LT-ST-260. We confirm the size, colour, price and timing before printing.

Render pending
The brimThe low wide brim, unlit, on one ground.
Render pending
Switched onThe halo: a ring of light escaping upward through the top gap.
Render pending
The carrier ringThe 28 mm carrier ring seat. Not a clip fitter, and drawn so it cannot be one.
Render pending
Scale190 mm across, on a bedside table.

Table Halo 190

LT-ST-190

Price on request

A low, wide brim for a table lamp: most of the light goes down onto the surface and a ring of it escapes upward through the gap at the top, which is where the name comes from. It takes an E14 lampholder with a 28 mm ring. It seats on a carrier ring or a harp, which is what gives the brim its clean unbroken line.

Code: LT-ST-190
Size: 190 mm across, 105 mm tall
Wall: 1.2 mm nominal
Material: Virgin PETG, printed, translucent; Stainless steel carrier ring seat, bought in, 28 mm
It takes: An E14 lampholder with a 28 mm carrier ring, or a harp. Not a clip fitter.
Bulb: An LED, up to 6 W and 45 mm across the envelope
Clearance: 42.5 mm from the widest point of the bulb to the nearest printed surface
Openings: Open at both ends. 74 mm clear at the top, 184 mm clear at the bottom.
Yours to choose: The lampholder and shade ring, the cord set or the stem, the switch, the plug and the bulb.
Colour: warm white by default, or unpigmented natural, pale sand
Weight: 245 g, the printed part alone
Made to order: The brim diameter, 150 to 260 mm. Height, the 28 mm ring seat, the top opening ratio and the 40 mm clearance minimum stay as drawn. A wider brim is a wider pool on the desk and a thinner halo.
Lead time: 7 to 10 days, printed after it is ordered
Printed: 0.12 mm layers, 3 perimeters, upright, small opening down, about 9 hours on the machine

Why this shapeA table lamp is looked down on as often as it is looked across at, so the top opening is a part of the object rather than a hole left over. At 74 mm it throws an obvious ring of light on the ceiling, which is where the name came from.

Make yours Instructions

Review and request

Request Table Halo 190 · LT-ST-190. We confirm the size, colour, price and timing before printing.

Shade only, your fitting

A shade goes on the lampholder you already own.

What you get: The printed shade, with a seat cut for a standard shade ring at the diameter on its record.
Yours to choose: The lampholder and its shade ring, the cord set and ceiling rose or the stem, harp and base, the switch, the plug, and the bulb. That is what lets a shade be drawn for the fitting already in your room.
The bulb: An LED, up to the wattage and envelope diameter on the piece. The bulb is your choice, so the light in the room is yours to set, and the shade is drawn to make whatever you choose look considered. The instructions are behind the QR code on the shade, so you are never guessing.
Sizes: One dimension on every shade is yours, inside the range on its record. Everything else stays as drawn, so the proportion survives the change.
Colours: Translucent and pale, because the glowing wall is the product. Unpigmented natural is the default.

Onward

The rest of the catalogue.

Small decor

Decorative pieces that work with the light falling on them: a wall of folded tiles, a screen that throws its pattern across the plaster.

Every piece

The whole catalogue on one page, with what each one fits.

How to order

What to send, and what comes back before anything is printed.