Every shade, first
Fit an LED bulb, and the light is yours to set.
Every shade here is drawn around an LED bulb at the size stated on its own record. LED runs cool and lasts for years, which is what lets a printed shade sit this close to it, so buy the next bulb to the same two numbers and it is the right bulb again.
Everything a shade needs from its fitting is written down here, so you are never guessing: the right holder, the right ring, the openings clear. Get those three and it drops straight on.
Ridge Pendant 280
LT-HG-280
An LED, up to 12 W and 65 mm across the envelope. Look for LED on the box and keep inside those two numbers, and the next bulb is as right as the first.
An E27 lampholder with a 40 mm shade ring. The holder, the ring, the cord set or stem, the switch and the plug are yours to choose, which is what lets the shade suit the fitting already in the room.
Seat the shade on the ring and check it sits square before the bulb goes in. Open at both ends. 96 mm clear at the top, 272 mm clear at the bottom. Keep those openings clear and it stays cool and true.
Check the bulb before you check the shade. When you change it, hold the new one against the two numbers here, 12 W and 65 mm, and look for LED on the box. Dust with a dry brush: a translucent wall shows a smear where an opaque one would not, and a minute with a brush keeps it reading as new. Lift the shade off the ring to clean it, once the bulb has gone cold.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Fit an LED bulb, never an incandescent or a halogen one. LED runs cool and lasts for years, and this shade is drawn around one. An LED puts its heat into its own base and stays cool at the face, and that is what lets a printed shade sit this close to it.
Cluster Cone 165
LT-HG-165
An LED, up to 6 W and 45 mm across the envelope. Look for LED on the box and keep inside those two numbers, and the next bulb is as right as the first.
An E14 lampholder with a 28 mm shade ring. The holder, the ring, the cord set or stem, the switch and the plug are yours to choose, which is what lets the shade suit the fitting already in the room.
Seat the shade on the ring and check it sits square before the bulb goes in. Open at both ends. 44 mm clear at the point, 134 mm clear at the mouth. Keep those openings clear and it stays cool and true.
Check the bulb first, as with every shade here: 6 W, 45 mm, LED on the box. A cone gathers dust in its point, so lift it off the ring and tip it out rather than pushing a cloth up into it. Hanging three at different drops looks best and keeps each one in clear air.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Fit an LED bulb, never an incandescent or a halogen one. LED runs cool and lasts for years, and this shade is drawn around one. An LED puts its heat into its own base and stays cool at the face, and that is what lets a printed shade sit this close to it.
Column Shade 260
LT-ST-260
An LED, up to 15 W and 65 mm across the envelope. Look for LED on the box and keep inside those two numbers, and the next bulb is as right as the first.
An E27 lampholder on a harp and finial, or a 40 mm carrier ring. The holder, the ring, the cord set or stem, the switch and the plug are yours to choose, which is what lets the shade suit the fitting already in the room.
Seat the shade on the ring and check it sits square before the bulb goes in. Open at both ends. 200 mm clear at the top, 216 mm clear at the bottom. Keep those openings clear and it stays cool and true.
Check the bulb first: 15 W, 65 mm, LED on the box. Keep the top opening clear and the shade stays cool and true for years. Wipe with a dry cloth, cold.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Fit an LED bulb, never an incandescent or a halogen one. LED runs cool and lasts for years, and this shade is drawn around one. An LED puts its heat into its own base and stays cool at the face, and that is what lets a printed shade sit this close to it.
Table Halo 190
LT-ST-190
An LED, up to 6 W and 45 mm across the envelope. Look for LED on the box and keep inside those two numbers, and the next bulb is as right as the first.
An E14 lampholder with a 28 mm carrier ring, or a harp. Not a clip fitter. The holder, the ring, the cord set or stem, the switch and the plug are yours to choose, which is what lets the shade suit the fitting already in the room.
Seat the shade on the ring and check it sits square before the bulb goes in. Open at both ends. 74 mm clear at the top, 184 mm clear at the bottom. Keep those openings clear and it stays cool and true.
Check the bulb first: 6 W, 45 mm, LED on the box. This shade seats on a carrier ring or a harp, so check your table lamp has one before you order and it will drop straight on. Wipe cold and dry.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Fit an LED bulb, never an incandescent or a halogen one. LED runs cool and lasts for years, and this shade is drawn around one. An LED puts its heat into its own base and stays cool at the face, and that is what lets a printed shade sit this close to it.
Fold Panel 300
LT-SD-300
Two screws at 240 mm centres or four adhesive pads. Tiles key into each other on all four edges.
Dust it with a dry brush, going along the fold rather than across it. Each tile carries itself, so hang other things from the wall and leave the tiles to be the wall. One tile can be reprinted and swapped without taking the rest down, which is why it keys rather than glues; a new tile reads a touch fresher than its neighbours at first.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Shadow Screen 260
LT-SD-260
214 perforations at 6 mm, 18 percent open area, on a foot that leans it back. Nothing to fix and nothing to fit: it stands where you put it.
Dust it with a dry brush, going with the perforations rather than across them. Stand it a hand's width or more from the lamp, which is also where the pattern is sharpest, and carry it by the frame. Wipe cold and dry.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Plain
LT-LC-003
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Eight facets
LT-LC-005
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Six facets
LT-LC-004
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Broad flute
LT-LC-009
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Vertical rib
LT-LC-001
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Twisted rib
LT-LC-002
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Filled-cell shell
LT-LC-015
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Soft star
LT-LC-008
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Low-poly cup
LT-LC-011
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Dimples
LT-LC-006
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Quilt
LT-LC-007
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Ripple column
LT-LC-013
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Rounded rib
LT-LC-010
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Spiral ring
LT-LC-012
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Twisted square
LT-LC-014
Includes one removable 37.2 mm LED tealight.
Battery LED only. Never use a burning candle. Lift out the LED before wiping the holder with a damp cloth.
The file stays with us, so a second one, a replacement or a matching piece for the next room is a message and a code. If you want it a little different, that is an edit to the drawing rather than a new one.
Anything you want to ask?
Send the code on your piece in a message and the answer comes back from the person who drew it.